FlashFXP Forums - View Single Post

liiight · 11-23-2006, 11:48 PM

Before I start, I ,must say that I've read every thread i could find in this forum about the subject, and viewed all the possible solutions.

I am using ver 3.2.0 build 1080
The site i'm connecting to support PRET:

Code:

[R] 215 UNIX system type.
[R] FEAT
[R] 211-Extensions supported:
[R]  PRET
[R]  AUTH SSL
[R]  PBSZ
[R]  CPSV
[R]  SSCN
[R]  MLST type*,x.crc32*,size*,modify*,unix.owner*,unix.group*,x.slaves*,x.xfertime*
[R]  CLNT
[R]  NOOP
[R] 211 End
[R] CLNT FlashFXP 3.2.0.1080
[R] 200 Command okay

This is the message i get when trying to direct d/l:

Code:

[R] PORT 192,168,2,100,4,8
[R] 501- ==YOU'RE BEHIND A NAT ROUTER==
[R] 501- Configure the firewall settings of your FTP client
[R] 501-   to use your real IP: x.x.x.x
[R] 501- And set up port forwarding in your router.
[R] 501- Or you can just use a PRET capable client, see
[R] 501    http://drftpd.org/ for PRET capable clients

This is the message that i get when trying to FXP:

Code:

[R] PRET RETR xxx.xxx
[R] 530 No transfer-slave(s) available
[R] PASV
[R] 500 You need to use a client supporting PRET (PRE Transfer) to use PASV
[L] Transfer Failed!

The "Site does not support FEAT command" IS NOT checked.
I've limited the local port range via the settings, and forwarded the same ports withing the router (EDIMAX 6104KP).

Like others here, it seems that it suddenly stopeed working, since it used to work fine up until a few days ago, with no changes to the program, or the network.

Am i missing something?

11-23-2006, 11:48 PM
liiight Junior Member Join Date: Nov 2006 Posts: 5	Problems with the PRET command Before I start, I ,must say that I've read every thread i could find in this forum about the subject, and viewed all the possible solutions. I am using ver 3.2.0 build 1080 The site i'm connecting to support PRET: Code: [R] 215 UNIX system type. [R] FEAT [R] 211-Extensions supported: [R] PRET [R] AUTH SSL [R] PBSZ [R] CPSV [R] SSCN [R] MLST type,x.crc32,size,modify,unix.owner,unix.group,x.slaves,x.xfertime [R] CLNT [R] NOOP [R] 211 End [R] CLNT FlashFXP 3.2.0.1080 [R] 200 Command okay This is the message i get when trying to direct d/l: Code: [R] PORT 192,168,2,100,4,8 [R] 501- ==YOU'RE BEHIND A NAT ROUTER== [R] 501- Configure the firewall settings of your FTP client [R] 501- to use your real IP: x.x.x.x [R] 501- And set up port forwarding in your router. [R] 501- Or you can just use a PRET capable client, see [R] 501 http://drftpd.org/ for PRET capable clients This is the message that i get when trying to FXP: Code: [R] PRET RETR xxx.xxx [R] 530 No transfer-slave(s) available [R] PASV [R] 500 You need to use a client supporting PRET (PRE Transfer) to use PASV [L] Transfer Failed! The "Site does not support FEAT command" IS NOT checked. I've limited the local port range via the settings, and forwarded the same ports withing the router (EDIMAX 6104KP). Like others here, it seems that it suddenly stopeed working, since it used to work fine up until a few days ago, with no changes to the program, or the network. Am i missing something?